Search

Cementitious Smoothing Levelling Coat Mortar and Pore Sealer

PRODUCT DESCRIPTION Tasir ®-MT02 is a one component cementitious polymer modified mortar. USES ▪ As a concrete pore sealer/levelling mortar/smooth- ing coat ▪ Repairing minor defects ▪ Thin layer render ▪ Repairing pores and honeycombed concrete ▪ For exterior and interior use CHARACTERISTICS /......

Send InquiryChat Now

PRODUCT DESCRIPTION

Tasir ®-MT02  is a one component cementitious polymer modified mortar.


cementitious-smoothing-levelling-coat-mortar30282448666cementitious-smoothing-levelling-coat-mortar34395046772


USES

▪ As a concrete pore sealer/levelling mortar/smooth- ing coat

▪ Repairing minor defects

▪ Thin layer render

▪ Repairing pores and honeycombed concrete

▪ For exterior and interior use

 

CHARACTERISTICS / ADVANTAGES

▪ Pre-bagged for quality

▪ Just add water

▪ Compatible wit Tasir ®-FerroGard  corrosion inhibit- or

▪ Compatible with Tasir ®-Top and Tasir ®-MTmortars

▪ Overcoatable with Tasir -gard coatings

▪ Sprayable by wet spray method


PRODUCT INFORMATION


SUBSTRATE QUALITY / PRE-TREATMENT

The concrete shall be free from dust, loose material, surface contamination, existing renders, laitance coat- ings, oil and other materials which reduce bond or pre- vent suction or wetting of the smoothing coat.

Delaminated, weak, damaged and deteriorated con- crete should be repaired using MT repair mortars. High spots can be removed by grinding.

Concrete surface should be cleaned and roughened us- ing suitable abrasive blast cleaning techniques or high pressure waterblasting [up to 60 mPa (9000 psi)] tech- niques to achieve acceptable adhesion to the sub- strate. Adhesion test average must be >0.8 N/mm2 with no single value below 0.5 N/mm2 for crack bridging coatings and 1.0 N/mm2 with no single value below 0.7 N/mm2 for rigid coatings.


MIXING

Tasir ®-MT02 can be mixed with a slow speed (< 500 rpm) electric drill mixer.

Pour the water in the correct proportion into a suit- able mixing container. While stirring slowly, add the powder to the water. Mix thoroughly for at least 3 minutes to the required consistency.


APPLICATION

Smoothing Coat/Levelling Mortar

The surface should be pre-wetted to a saturated sur- face dry condition before application. Pre-fill surface defects before applying as a smoothing coat. Apply Tasir ®-MT02 by spatula or trowel to the re- quired thickness and finish. Where Tasir ®-MT02 is to be overcoated, finishing with a moist neo- prene sponge or brush after initial set has taken place is recommended to provide a key

for the coating. Do not overwork Tasir ®-MT02 during or after applying. Should Tasir ®-MT02 mortar be wetted during the initial cure period a white ‘bloom’ may be produced on the surface. This however, does not affect the long term properties of the mortar.

Pore filler:

Tightly trowel over surface and force into pores and other surface defects. Before overcoating remove ex- cess material from surface while wet and wash down if necessary when dry to remove any dust deposits which may affect the bond of subsequent coatings.


CURING TREATMENT

It is essential to cure the repair mortar immediately after application for a minimum of 3 days to ensure full cement hydration and to minimise cracking. Use polythene sheeting taped down at the edges or other approved method. Curing compounds shall not be used if smoothing coat is to be overcoated.


CLEANING OF TOOLS

Clean all tools and application equipment with water immediately after use. Hardened/cured material can only be mechanically removed.


LIMITATIONS

▪ Avoid application in direct sun and/or strong wind and/or rain.

▪ Do not add water over recommended dosage.

▪ Apply only to sound, prepared substrates.

▪ Do not add additional water during the surface finish- ing as this will cause discoloration and cracking.

▪ Protect freshly applied material from freezing.


VALUE BASE

All technical data stated in this Product Data Sheet are based on laboratory tests. Actual measured data may vary due to circumstances beyond our control.


LOCAL RESTRICTIONS

Please note that as a result of specific local regula- tions the performance of this product may vary from country to country. Please consult the local Product Data Sheet for the exact description of the application fields.


ECOLOGY, HEALTH AND SAFETY

For information and advice on the safe handling, stor- age and disposal of chemical products, users shall refer to the most recent Safety Data Sheet (SDS) containing physical, ecological, toxicological and other safety-re- lated data.

 

LEGAL NOTES

Please note that as a result of specific local regula- tions the performance of this product may vary from country to country. Please consult the local Product Data Sheet for the exact description of the application fields.


Tasir Construction Material&Technology Corporate Headquarters

Tianda Block, Jianggan District, Hangzhou City, Zhejiang Province, China

Tel: +86-571-28119206 

Fax: +86-571-28197878

groutmaterial.com


Specifications Subject to Change.

For most current version of datasheet, go to groutmaterial.com

© 2018Tasir Construction Material&TechnologyCp.,Ltd | 08-21-2018 Rev. H | China Owned & Operated


Hot Tags: cementitious smoothing levelling coat mortar and pore sealer, China, suppliers, manufacturers, cheap, made in China
Related Products
Copyright © Zhejiang Taizheng Construction Material Co.,Ltd All Rights Reserved.