Search

Fast Curing Anchoring Adhesive

PRODUCT DESCRIPTION Solvent and styrene free based, two-component poly- ester anchoring adhesive. USES Tasir®- AnchorFix may only be used by experienced professionals. As a fast curing anchoring adhesive for all grades of: ▪ Rebars / reinforcing steel ▪ Threaded rods ▪ Bolts and special......

Send InquiryChat Now

PRODUCT DESCRIPTION

Solvent and styrene free based, two-component poly- ester anchoring adhesive.


fast-curing-anchoring-adhesive56504844493fast-curing-anchoring-adhesive21266140634


USES

Tasir®- AnchorFix may only be used by experienced professionals.

As a fast curing anchoring adhesive for all grades of:

▪ Rebars / reinforcing steel

▪ Threaded rods

▪ Bolts and special fastening systems

▪ Concrete

▪ Hollow and solid masonry

▪ Hard natural stone*

▪ Solid rock*

* These substrates may vary greatly, in particular with regard to strength, composition and porosity. There- fore, for each application the suitability of Tasir®- AnchorFix must be tested by first applying Tasir®- AnchorFix Adhesive only to a sample area. Check in particular bond strength, surface staining and discol- ouration.

 

CHARACTERISTICS / ADVANTAGES

▪ Fast curing

▪ Standard guns can be used

▪ Can be used at low temperatures

▪ High load capacity

▪ ETA Approval available

▪ Non-sag, even overhead

▪ Styrene-free

▪ Low odour

▪ Low wastage


PRODUCT INFORMATION

11.jpg


TECHNICAL INFORMATION

22.jpg


APPLICATION INFORMATION

33.jpg

44.jpg


APPLICATION INSTRUCTIONS

SUBSTRATE QUALITY

▪ Mortar and concrete must be at the required strength. No need to be 28 days old.

▪ Substrate strength (concrete, masonry, natural stone) must be verified.

▪ Pull-out tests must be carried out if the substrate strength is unknown.

▪ The anchor hole must always be clean, dry, free from oil and grease etc.

▪ Loose particles must be removed from the holes.

▪ Threaded rods and rebars have to be cleaned thor- oughly from any oil, grease or any other substances and particles such as dirt etc.


MIXING

Getting the cartridge ready: 300 ml / 550 ml

image015(001).jpg1. Unscrew the cap
image017(001).jpg2. Cut the film
image019(001).jpg3. Screw on the static mixer
image021(001).jpg4. Place the cartridge in- to the gun and start ap- plication

When the work is interrupted the static mixer can re- main on the cartridge after the gun pressure has been relieved. If the resin has hardened in the nozzle when work is resumed, a new nozzle must be attached.


APPLICATION METHOD / TOOLS

Anchors in solid masonry / concrete

image023.jpgDrilling of hole with an electric drill to the dia- meter and depth re- quired. Drill hole diamet- er must be in accordance with anchor size.
image025.jpg

The drill hole must be cleaned with a blow pump or by compressed air, starting from the bot- tom of the hole. (at least 2x)

Important: use oil-free compressors.

image027(001).jpgThe drill hole must be thoroughly cleaned with the special steel brush (brush at least 2x). The diameter of the brush must be larger than the diameter of the drill hole.
image025.jpg

The drill hole must be cleaned with a blow pump or by compressed air, starting from the bot- tom of the hole. (at least 2x)

Important: use oil-free compressors.

image027(001).jpgThe drill hole must be thoroughly cleaned with the special steel brush (brush at least 2x). The diameter of the brush must be larger than the diameter of the drill hole.
image025.jpg

The drill hole must be cleaned with a blow pump or by compressed air, starting from the bot- tom of the hole. (at least 2x)

Important: use oil-free compressors.

image032(001).jpgPump approx. twice until both parts come out uni- formly. Do not use this material. Release the gun pressure and clean the cartridge opening with a cloth.
image034.jpgInject the adhesive into the hole, starting from the bottom, while slowly drawing back the static mixer. In any case avoid entrapping air. For deep holes extension tubing can be used.
image036.jpg

Insert the anchor with a rotary motion into the filled drill hole. Some ad- hesive must come out of the hole.

Important: the anchor must be placed within the open time.

image038.jpgDuring the resin harden- ing time the anchor must not be moved or loaded. Wash tools immediately with Sika® Colma Cleaner. Wash hands and skin thoroughly with warm soap water.


Anchors in hollow blocks

image040(001).jpg

Drilling of hole with an electric drill to the dia- meter and depth re- quired. Drill hole diamet- er must be in accordance with anchor-and perfor- ated sleeve size.

Note: with hollow materi- al do not use rotary ham- mer drills.

image042(001).jpgThe drill hole must be thoroughly cleaned with a round brush (brush at least 1x). The diameter of the brush must be larger than the diameter of the drill hole.
image044(001).jpg

The drill hole must be cleaned after each clean- ing step with a blow pump or by compressed air, starting from the bot- tom of the hole (pump at least 1x).

Important: use oil-free compressors.

image054(001).jpgInsert perforated sleeve completely into the drill hole.
image032(001).jpgPump approx. twice until both parts come out uni- formly. Do not use this material. Release the gun pressure and clean the cartridge opening with a cloth.
image046(001).jpgInject the adhesive into the perforated sleeve, starting from the bottom, while slowly drawing back the static mixer. In any case avoid entrapping air.
image048(001).jpgClose the cap from the perforated sleeve to avoid some escape of the resin during entering the steel rod.
image050(001).jpg

Insert the anchor with a rotary motion into the filled perforated sleeve. Use the adequate steel rod size.

Important: the anchor must be placed within the open time.

image052(001).jpgDuring the resin harden- ing time the anchor must not be moved or loaded. Wash tools immediately with Sika® Colma Cleaner. Wash hands and skin thoroughly with warm soap water.


CLEANING OF TOOLS

Clean tools and application equipment with Tasir® Cleaner immediately after use. Hardened / cured material can only be mechanically removed.

 

FURTHER DOCUMENTS

For design details, please refer to the separate docu- mentation provided:

Technical Documentation Tasir®- AnchorFix Techinical.


VALUE BASE

All technical data stated in this Product Data Sheet are based on laboratory tests. Actual measured data may vary due to circumstances beyond our control.


LOCAL RESTRICTIONS

Please note that as a result of specific local regula- tions the performance of this product may vary from country to country. Please consult the local Product Data Sheet for the exact description of the application fields.


ECOLOGY, HEALTH AND SAFETY

For information and advice on the safe handling, stor- age and disposal of chemical products, users shall refer to the most recent Safety Data Sheet (SDS) containing physical, ecological, toxicological and other safety-re- lated data.

 

LEGAL NOTES

The information, and, in particular, the recommenda- tions relating to the application and end-use of Tasir products, are given in good faith based on Tasir's cur- rent knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Tasir’s recommenda- tions. In practice, the differences in materials, sub- strates and actual site conditions are such that no war- ranty in respect of merchantability or of fitness for a particular purpose, nor any liability arising out of any legal relationship whatsoever, can be inferred either from this information, or from any written recom- mendations, or from any other advice offered. The user of the product must test the product’s suitability for the intended application and purpose. Tasir re- serves the right to change the properties of its products. The proprietary rights of third parties must be observed. All orders are accepted subject to our current terms of sale and delivery. Users must always refer to the most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.


Tasir Construction Material&Technology Corporate Headquarters

Tianda Block, Jianggan District, Hangzhou City, Zhejiang Province, China

Tel: +86-571-28119206 

Fax: +86-571-28197878

groutmaterial.com


Specifications Subject to Change.

For most current version of datasheet, go to groutmaterial.com

© 2018Tasir Construction Material&TechnologyCp.,Ltd | 08-21-2018 Rev. H | China Owned & Operated


Hot Tags: fast curing anchoring adhesive, China, suppliers, manufacturers, cheap, made in China
Related Products
Copyright © Zhejiang Taizheng Construction Material Co.,Ltd All Rights Reserved.