Search

Segmental Bridge Adhesive

DESCRIPTION Tasir® Segmental Bridge Adhesive and Tasir® Segmental Bridge Adhesive LT are 100% solids, two-component structural epoxy compounds used in the installation or repair of segmental bridges and structures. Two versions are available for varying temperature ranges: Segmental Bridge......

Send InquiryChat Now

DESCRIPTION

Tasir® Segmental Bridge Adhesive and Tasir® Segmental Bridge Adhesive LT are 100% solids, two-component structural epoxy compounds used in the installation or repair of segmental bridges and structures. Two versions are available for varying temperature ranges: Segmental Bridge Adhesive for 60-120°F (16-49°C), and Segmental Bridge Adhesive LT for 20-80°F (-7 - 27°C). The non-abrasive gels have low-creep characteristics and enhanced tensile strength. Both conform to the current ASTM C-881, Types I, IV, VI and VII, Grade-3, Class-B/ C, AASHTO M-235 specifications.


segmental-bridge-adhesive18102293520segmental-bridge-adhesive32573616309


USES

● Bonding precast concrete segments

● Bonding steel plates to concrete

● Fasten bolts into walls

● Gap & crack filling


BENEFITS

● Easy 1 to 1 mix ratio

● V.O.C. compliant, 100% s

● Excellent adhesion to concr

● Easy manual mixing and trowel application 

● Good solvent and chemical resistance 

● Excellent abrasion and impact resistance


PACKAGING & YIELD

Tasir®Segmental Bridge Adhesive and Tasir® Segmental Bridge Adhesive LT come packaged in kits made up of two one-gallon con- tainers (7.6 liters). Coverage is approximately 26 ft2 (2.42m2) at 1/8” (0.32cm) thickness per kit.


SHELF LIFE

Two years in original unopened packaging when stored in dry conditions at 40°F - 90°F (4°C - 32°C).

Typical Properties at 70°F (21°C)

Resin

Epoxy Polyamide

Solids by Volume

100%

Mixing Ratio: A:B by volume

1:1

Elongation, D 638

1.64%

Cure Time

Dry to Touch (Approx. 2 hours)

Color

Grey

Slant Shear Strength, ASTM C882 — 2 days

4,500 psi (31.0 MPa) - Concrete to concrete

4,200 psi (28.9 MPa) - Concrete to steel
3,400 psi (23.4 MPa) - SSD to SSD concrete

Gel Time

Segmental Bridge Adhesive

Segmental Bridge Adhesive LT

60°F (15°C)

100°F (38°C)

120°F (49°C)

20°F (-7°C)

40°F (4°C)

80°F (27°C)

60 mins

45 mins

30 mins

90 mins

45 mins

30 mins

Compressive Strength, ASTM D 695

Temperature Range: 60-120°F (15 - 49°C)

Temperature Range: 20-80°F (-7 - 27°C)

@ 90°F (32°C)

@ 40°F (4°C)

1 day

3 days

7 days

1 day

3 days

7 days

8,000 psi
(55.2 MPa)

8,700 psi
(60.0 MPa)

9,000 psi
(62.1 MPa)

3,500 psi
(24.1 MPa)

4,000 psi
(27.6 MPa)

4,250 psi
(29.3 MPa)

The data shown above reflects typical results based on laboratory testing under controlled conditions. Reasonable variations from the data shown above may result.

 

PLACEMENT GUIDELINES FOR SEGMENTAL BRIDGE ADHESIVES

1. SURFACE PREPARATION: Concrete surfaces should be a minimum of 28 days old and may be dry or damp, but free of standing water. Surfaces must be clean, sound and free of any dirt, laitance or other bond inhibiting contaminants. High-pressure water blasting or abrasive blasting of surfaces is recommended. A concrete surface profile (CSP) of 3 to 4 in accordance with ICRI Technical Guideline 03732 should be achieved. A steel surface profile of SSPC-SP-6 should be achieved. Blow prepared surfaces clean.

2. MIXING INSTRUCTIONS: Material should be preconditioned to between 45°F and 85°F (7°C and 30°C) before using. Premix each component thoroughly. Proportion equal parts by volume of Component A and Component B into a clean pail. Stir or mix thoroughly for three minutes by hand with a low speed drill (400 to 600 rpm) until uniform in color. Avoid entrapping air. Mix only a quantity that can be placed within a 30-minute working time.

3. METHOD OF PLACEMENT: Apply neat to the prepared substrate, working into substrate for positive adhesion. Apply 1/8” (3 mm) to one face, or 1/16” (1.5 mm) thickness to both faces, dependent on project requirements. Secure elements firmly until adhesive has cured.

4. CLEAN-UP: Paint thinner, acetone or similar solvent may be used for clean up of tools and equipment. Cured material can only be removed mechanically.

NOTE: PRIOR TO APPLICATION, READ ALL PRODUCT PACKAGING THOROUGHLY. For more detailed placement procedures, refer to Tasir® installation guidelines or call Tasir® Products’ Engineering and Technical Service Center at +86-571-87569602.


CONSIDERATIONS

● Minimum application temperature of substrate is 20ºF (-7ºC) and rising, but must be frost free when using Segmental Bridge Adhesive LT.

● Do not thin with solvents.


CAUTION

Irritant, toxic, strong sensitizer. Contains epoxy resin and amine. This product may cause skin irritation. Do not inhale vapors. Provide adequate ventilation. Protect against contact with skin and eyes. Wear rubber gloves, long sleeve shirt, goggles with side shields. In case of contact with eyes, flush repeatedly with water and contact a physician. Areas of skin contact should be promptly washed with soap and water. Wash thoroughly after handling. Do not take internally. Keep product out of reach of children. Keep container closed when not in use. PRIOR TO USE, REFER TO SAFETY DATA SHEET.

For worldwide availability, additional product information and technical support, contact your local Tasir® distributor, local sales representative, or call Tasir® Products'Engineering and Technical Service Center at +86-571-87569602.

SKU/PRODUCT CODE

DESCRIPTION

# UNITS/PALLET

UNIT SIZE

34645

Tasir® Segmental Bridge Adhesive 2 gallon kit

50

Resin (A): 1 gal. (3.8 L)
Hardener (B): 1 gal. (3.8 L)

34640

Tasir® Segmental Bridge Adhesive LT 2 gallon kit

50

Resin (A): 1 gal. (3.8 L)
Hardener (B): 1 gal. (3.8 L)

WARRANTY: “Tasir PRODUCTS ARE MANUFACTURED TO BE FREE OF MANUFACTURING DEFECTS AND TO MEET FSP’S CURRENT PUBLISHED PHYSICAL PROPERTIES WHEN APPLIED IN ACCORDANCE WITH Tasir'S DIRECTIONS AND TESTED IN ACCORDANCE WITH ASTM AND Tasir STANDARDS. HOWEVER, SHOULD THERE BE DEFECTS OF MANUFACTURING OF ANY KIND, THE SOLE RIGHT OF THE USER WILL BE TO RETURN ALL MATERIALS ALLEGED TO BE DEFECTIVE, FREIGHT PREPAID TO Tasir, FOR REPLACEMENT. THERE ARE NO OTHER WARRANTIES BY Tasir OF ANY NATURE WHATSOEVER, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IN CONNECTION WITH THIS PRODUCT. Tasir SHALL NOT BE LIABLE FOR DAMAGES OF ANY SORT, INCLUDING PUNITIVE, ACTUAL, REMOTE, OR CONSEQUENTIAL DAMAGES, RESULTING FROM ANY CLAIMS OF BREACH OF CONTRACT, BREACH OF ANY WARRANTY, WHETHER EXPRESSED OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR FROM ANY OTHER CAUSE WHATSOEVER. Tasir SHALL ALSO NOT BE RESPONSIBLE FOR USE OF THIS PRODUCT IN A MANNER TO INFRINGE ON ANY PATENT HELD BY OTHERS.”


Tasir Construction Material&Technology Corporate Headquarters

Tianda Block, Jianggan District, Hangzhou City, Zhejiang Province, China


Specifications Subject to Change.

For most current version of datasheet, go to groutmaterial.com

© 2018Tasir Construction Material&TechnologyCp.,Ltd | 08-21-2018 Rev. H | China Owned & Operated

• Tel: +86-571-28119206

• Fax: +86-571-28197878

groutmaterial.com


Hot Tags: segmental bridge adhesive, China, suppliers, manufacturers, cheap, made in China
Related Products
Copyright © Zhejiang Taizheng Construction Material Co.,Ltd All Rights Reserved.