Search

Substrate Void Filler

PRODUCT DESCRIPTION Tasir®substrate void filler is a one component, 100% solids, solvent-free adhesive and void filler for use on multiple substrates. This product can be used to fill voids or gaps of up to 3/4” and is perfect as a sealer/adhesive for use with the Tasir® Centrifugal-Cast......

Send InquiryChat Now

PRODUCT DESCRIPTION

Tasir®substrate void filler is a one component, 100% solids, solvent-free adhesive and void filler for use on multiple substrates. This product can be used to fill voids or gaps of up to 3/4” and is perfect as a sealer/adhesive for use with the Tasir® Centrifugal-Cast industrial pipe repair system.


substrate-void-filler23358184831substrate-void-filler30229206094


ADVANTAGES

• Fills gaps up to 3/4”

• Superior shore hardness

• Remains flexible and suitable for use where shock, vibration, shrinking or swelling are concerns.

• Environmentally friendly—solvent free, isocyanate free and low VOC

• Tack free in < 30 minutes for increased productivity

• Non-sag for ease of placement


USES

• Fill and repair voids in multiple substrates

• Seal industrial pipe voids prior to application of repair mortar

• Part of the complete Tasir® Centrifugal-Cast industrial pipe repair system


PACKAGING

Tasir® substrate void filler is packaged in 20 oz. sausage tubes for use in manual or pneumatic guns.


SHELF LIFE

One year from manufacture date in original unopened packaging when stored in dry conditions below 80°F (27°C).

Note: Due to the wide variety of substrates, preparation methods, application methods and environments, always test a small area of substrate to verify desired results.

TYPICAL PROPERTIES AT 70°F (21°C)

Cured Properties at 21 Days

Tensile Bond (Fiberglass)

175 psi (1.20 MPa)

Hardness, Shore A, ASTM D 2240

60

Tensile Strength, ASTM D 412

260 psi (1.8 MPa)

Elongation, ASTM D 412

250%

Peel Strength, ASTM D 1004

60 lbs/in (1,056 kg/m)

Uncured Properties

Cure Rate

1/4" - 16 hours

VOC Content

< 30g/liter

The data shown above reflects typical results based on laboratory testing under controlled conditions. Reasonable variations from the data shown above may result. Test methods are modified where applicable.

 

PLACEMENT GUIDELINES

1. SURFACE PREPARATION: Surfaces must be clean, sound, and free of any growth, dirt, oxidation, rust or other bond inhibiting contaminants. High-pressure water blasting or abrasive blasting of surfaces is recommended. Coat areas as soon as possible after surface preparation to minimize corrosion to newly prepared surfaces.

2. PLACEMENT: Place cartridge in appropriate sausage gun with applicable tip to achieve desired bead of material. Dispense following application gun’s instructions. Tasir® substrate void filler should be applied at a surface temperature of at least 40°F (5°C) or higher.

3. CLEAN-UP: Mineral Spirits, Denatured Alcohol, or VM&P solvent may be used for clean up of tools and equipment.

NOTE: PRIOR TO APPLICATION, READ ALL PRODUCT PACKAGING THOROUGHLY. For more detailed placement procedures, refer to Tasir®installation guidelines or call Tasir® Products'Engineering and Technical Service Center at +86-571-87569602.


CAUTION:

Irritant, toxic, strong sensitizer. This product may cause skin irritation. Do not inhale vapors. Provide adequate ventilation. Protect against contact with skin and eyes. Wear rubber gloves, long sleeve shirt, goggles with side shields. In case of contact with eyes, flush repeatedly with water and contact a physician. Areas of skin contact should be promptly washed with soap and water. Wash thoroughly after handling. Do not take internally. Keep product out of reach of children. Keep container closed when not in use. PRIOR TO USE, REFER TO SAFETY DATA SHEET.

For worldwide availability, additional product information and technical support, contact your local Tasir distributor, local sales representative, or call Tasir Products'Engineering and Technical Service Center at +86-571-87569602.

SKU/PRODUCT CODE

DESCRIPTION

# UNITS/PALLET

UNIT SIZE

SVF

Tasir®substrate void filler

45

20 oz. (0.6 kg) Sausage Tubes
12 tubes / case

WARRANTY: “Tasir PRODUCTS ARE MANUFACTURED TO BE FREE OF MANUFACTURING DEFECTS AND TO MEET FSP'S CURRENT PUBLISHED PHYSICAL PROPERTIES WHEN APPLIED IN ACCORDANCE WITH Tasir'S DIRECTIONS AND TESTED IN ACCORDANCE WITH ASTM AND Tasir STANDARDS. HOWEVER, SHOULD THERE BE DEFECTS OF MANUFACTURING OF ANY KIND, THE SOLE RIGHT OF THE USER WILL BE TO RETURN ALL MATERIALS ALLEGED TO BE DEFECTIVE, FREIGHT PREPAID TO Tasir, FOR REPLACEMENT. THERE ARE NO OTHER WARRANTIES BY Tasir OF ANY NATURE WHATSOEVER, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IN CONNECTION WITH THIS PRODUCT. Tasir SHALL NOT BE LIABLE FOR DAMAGES OF ANY SORT, INCLUDING PUNITIVE, ACTUAL, REMOTE, OR CONSEQUENTIAL DAMAGES, RESULTING FROM ANY CLAIMS OF BREACH OF CONTRACT, BREACH OF ANY WARRANTY, WHETHER EXPRESSED OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR FROM ANY OTHER CAUSE WHATSOEVER. Tasir SHALL ALSO NOT BE RESPONSIBLE FOR USE OF THIS PRODUCT IN A MANNER TO INFRINGE ON ANY PATENT HELD BY OTHERS.”


Tasir Construction Material&Technology Corporate Headquarters

Tianda Block, Jianggan District, Hangzhou City, Zhejiang Province, China

 

Specifications Subject to Change.

For most current version of datasheet, go to groutmaterial.com

© 2018Tasir Construction Material&TechnologyCp.,Ltd | 08-21-2018 Rev. H | China Owned & Operated

• Tel: +86-571-28119206

• Fax: +86-571-28197878

groutmaterial.com


Hot Tags: substrate void filler, China, suppliers, manufacturers, cheap, made in China
Related Products
Copyright © Zhejiang Taizheng Construction Material Co.,Ltd All Rights Reserved.