Search

Splash Zone Underwater Epoxy Mastic Coating

DESCRIPTION Tasir®Splash Zone is a 100% solids, two component epoxy compound used to protect metal, wood and concrete against corrosion and deterioration from salt or fresh water. Tasir®Splash Zone is designed for underwater or tidal zone placements. ADVANTAGES • Easy 1 to 1 Mix Ratio • V.O.C.......

Send InquiryChat Now

DESCRIPTION

Tasir®Splash Zone is a 100% solids, two component epoxy compound used to protect metal, wood and concrete against corrosion and deterioration from salt or fresh water. Tasir®Splash Zone is designed for underwater or tidal zone placements.


splash-zone-underwater-epoxy-mastic-coating24516169440splash-zone-underwater-epoxy-mastic-coating18248180816


ADVANTAGES

• Easy 1 to 1 Mix Ratio

• V.O.C. Compliant, 100% solid

• Excellent Adhesion to Concrete, steel, Wood and Fiberglass

• Can be Applied Underwater

• Good solvent and Chemical Resistance

• Excellent Abrasion and Impact Resistance

 

USES

Tasir®Splash Zone is used to repair and protect concrete, steel, wood, fiberglass, and aluminum from salt and fresh water in splash zone, tidal zone, and waterline applications.


SIZING & CONFIGURATION

Tasir®Splash Zone is available in two-gallon units (7.6 liters) where 1 gallon will cover approximately 13 sq. ft. at ⅛” thick (125 mils) or approximately 6.5 sq. ft. at ¼” thick (250 mils).


SHELF LIFE

One year in original unopened packaging when stored in dry conditions at 50°F - 90°F (10°C - 35°C).

Typical Properties of 70°F (21°C)

Resin System

Epoxy Polyamide

Solids by Volume

100%

Mixing Ratio by Volume (A:B)

1:1

Color

Medium Gray

Working Time

30 Minutes

Dry to Touch

2 Hours

Dry Hard

4 Hours

Full Cure

7 Days

Shore D Hardness (ASTM D2240)

4 Hours

50-60

7 Days

70-80

Adhesion (ASTM D4541)

Steel (Dry)

1,200 psi (8.3 MPa)

Fiberglass (Dry)

750 psi (5.2 psi)

Steel (Wet)

800 psi (5.5 MPa)

Fiberglass (Wet)

450 psi (3.1 MPa)

Adhesion (ASTM C1583)

Concrete (Dry)

800 psi (5.5 MPa)

Concrete (Wet)

400 psi (2.8 MPa)

Compressive Strength (ASTM C579A)

1 Day

2,500 psi (17.2 MPa)

3 Days

4,000 psi (27.6 MPa)

7 Days

4,600 psi (31.7 MPa)

28 Days

5,400 psi (37.2 MPa)

The data shown above reflects typical results based on laboratory testing under controlled conditions. Reasonable variations from the data shown above may result.

 

PLACEMENT GUIDELINES

SURFACE PREPARATION: Surfaces must be clean, sound, and free of any marine growth, dirt, oxidation, rust or other bond inhibiting contaminants. High-pressure water blasting or abrasive blasting of surfaces is recommended. Coat areas as soon as possible after surface preparation to minimize corrosion to newly prepared surfaces.

MIXING INSTRUCTIONS: Combine one part by volume Component A with one part by volume Component B (1:1 ratio) using gloved hands. Pre-wet gloves to avoid product from sticking during mixing. Mix and knead Component A and Component B together until a uniform medium gray color is obtained. Re-wet hands continuously during mixing. Apply material immediately after mixing. Apply by hand or trowel evenly in ⅛” to ¼” lifts. Firmly work material into substrate, displacing air or water.

CLEAN-UP: Paint thinner, acetone or similar solvent may be used for clean up tools and equipment.

NOTE: PRIOR TO APPLICATION, READ ALL PRODUCT PACKAGING THOROUGHLY. For more detailed placement procedures call Tasir Products'Engineering and Technical Service Center at +86-571-87569602.


CONSIDERATIONS

• Minimum application temperature of substrate is 50ºF (10ºC) and rising.

• Do not thin with solvents.

• When applied underwater or brought in contact with water before cure, the product will change color and develop a soft exterior layer. This exterior film facilitates further hardening of the material beneath.


CAUTION

Irritant, toxic, strong sensitizer. Contains epoxy resin and amine. This product may cause skin irritation. Do not inhale vapors. Provide adequate ventilation. Protect against contact with skin and eyes. Wear rubber gloves, long sleeve shirt, goggles with side shields. In case of contact with eyes, flush repeatedly with water and contact a physician. Areas of skin contact should be promptly washed with soap and water. Wash thoroughly after handling. Do not take internally. Keep product out of reach of children. Keep container closed when not in use. PRIOR TO USE, REFER TO SAFETY DATA SHEET.

For worldwide availability, additional product information and technical support, contact your local Tasir® distributor, local sales representative, or call Tasir® Products'Engineering and Technical Service Center at +86-571-87569602.

SKU / PRODUCT CODE

DESCRIPTION

#UNITS/PALLET

UNIT SIZE

SZ

Tasir®Splash Zone

50

Resin (A): 11 lbs. ( 5.0 kg) Hardener (B): 11 lbs. (5.0 kg)

WARRANTY: “Tasir PRODUCTS ARE MANUFACTURED TO BE FREE OF MANUFACTURING DEFECTS AND TO MEET FSP'S CURRENT PUBLISHED PHYSICAL PROPERTIES WHEN APPLIED IN ACCORDANCE WITH Tasir'S DIRECTIONS AND TESTED IN ACCORDANCE WITH ASTM AND Tasir STANDARDS. HOWEVER, SHOULD THERE BE DEFECTS OF MANUFACTURING OF ANY KIND, THE SOLE RIGHT OF THE USER WILL BE TO RETURN ALL MATERIALS ALLEGED TO BE DEFECTIVE, FREIGHT PREPAID TO Tasir, FOR REPLACEMENT. THERE ARE NO OTHER WARRANTIES BY Tasir OF ANY NATURE WHATSOEVER, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IN CONNECTION WITH THIS PRODUCT. Tasir SHALL NOT BE LIABLE FOR DAMAGES OF ANY SORT, INCLUDING PUNITIVE, ACTUAL, REMOTE, OR CONSEQUENTIAL DAMAGES, RESULTING FROM ANY CLAIMS OF BREACH OF CONTRACT, BREACH OF ANY WARRANTY, WHETHER EXPRESSED OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR FROM ANY OTHER CAUSE WHATSOEVER. Tasir SHALL ALSO NOT BE RESPONSIBLE FOR USE OF THIS PRODUCT IN A MANNER TO INFRINGE ON ANY PATENT HELD BY OTHERS.”


Tasir Construction Material&Technology Corporate Headquarters

Tianda Block, Jianggan District, Hangzhou City, Zhejiang Province, China

 

Specifications Subject to Change.

For most current version of datasheet, go to groutmaterial.com

© 2018Tasir Construction Material&TechnologyCp.,Ltd | 08-21-2018 Rev. H | China Owned & Operated

• Tel: +86-571-28119206

• Fax: +86-571-28197878

groutmaterial.com


Hot Tags: splash zone underwater epoxy mastic coating, China, suppliers, manufacturers, cheap, made in China
Related Products
Copyright © Zhejiang Taizheng Construction Material Co.,Ltd All Rights Reserved.